Tag Archives: copper

Fall 2014

This Fall was relatively uneventful, but I did get a few minor projects done that have made Winter much more pleasant.  Also, I hosted wine-making workshop, which didn’t draw as many people as I imagined it would.  My volunteers from Chicago left at the beginning of October heading to another farm in Georgia.  They took my long-term volunteer, Billy, with them and as far as I know he’s still at that farm.

Rocket stove flue extended through the roofFirewood

The volunteers helped me split a good bit of firewood before they headed out, and I spent most of the Fall preparing for Winter in one way or another.  After they left I hauled some more logs, split them, and stacked up about a chord of wood.  I also cut down a big oak tree that had died over the summer and was leaning precariously towards the shed.  I cut that up, split it, and stacked it to cure for next Winter.

Flue Extension

I also finally extended the common house rocket stove flue pipe up through the porch roof.  The exhaust from the stove had been getting hung up under the porch and the moisture was condensing on the rafters to the point it was practically raining underneath the porch.   I used a dremel to cut a precise hole for the flue and a butyl rubber to seal around it.  The draft on the rocket stove has improved and I haven’t seen it back-smoke at all since the improvement.

Rocket-Powered Hot Water!

Rocket stove barrel copper hot water heating coilsLast winter I combined a couple of ideas and came up with a plan to have hot water year-round.  I built the solar hot water heating panel and installed the hot and cold barrels earlier in the spring, but the panel will only work in above-freezing temperatures because the water would freeze in the panel and burst the pipes.

I came up with the idea of using the same thermosiphon principle that worked on the solar panel, but wrapping copper tubing around the rocket stove barrel compared to the sun heating up the water in the panel.  It was a little tricky getting the copper wound tightly around the barrel, but luckily when you buy large sections of copper tubing it comes in coils to begin with making it easier to avoid crinkling the pipe when I bent it around the barrel.

After running the stove the average 6-8 hours it takes to heat the common house up for several days the water in the 55 gallon hot water barrel will be upwards of 120F.  The mass of the water and insulation on the barrel keeps the water hot for a couple of days, so it holds the heat almost the same amount of time as the house does.

 

Water System Taking Shape

Jason water system barrel bulkheadlsMy first volunteer of the season, Billy, arrived this past Thursday night from Louisiana.  I haven’t gotten the solar hot water collector or the rest of the basics of the common house water system up and running yet like I’d hoped.  I got a good a start on it, but I decided to do a bit of spring cleaning before people started arriving.  I also figured the volunteers would be interested in seeing the water system constructed, though perhaps not as interested in as I am.

Before I switched gears to cleaning, I procured and cut the lids off of what will be the gravity feed hot and cold water storage tanks.  With Jason’s help I got all of the bulkheads for the various inlets and outlets installed on them.  I built an overflow catchment tray above the shower where they’ll be housed in case of some kind of leak the water will now go down the shower drain and not into the battery/power room(yikes!).

solar-collector-copper-layoutI’ve gathered all of the parts and materials I need for the solar hot water collector and have gotten it configured how I want it.  Since this picture was taken I’ve also soldered the ends of the panel together(ie, the manafolds).  I also built and tested a form to mash aluminum flashing into “fins” which help redirect the heat into the copper tubing.

Next up is soldering the rest of the connections and testing to make sure it’s all water-tight. Then I’ll build the frame, stamp out the fins, install the insulation on the back and then build a stand for it in front of the common house.

Spring Cleaning

firepitI cleaned up a bunch of stuff at the small strawbale cabin I’m calling the “Pillbox”.  I finished constructing a closet rack with shelves in it, and generally cleaned up a bunch of down trees around it.  

I also jazzed up the main fire pit behind the common house and have been grudgingly pushing back all of the brush I’d piled up directly on the other side of the garden fence(mistake!) so that I can get at plants that are growing through the fence and shading out plants I actually want to grow.

cut-cedar-garden-tarpToday, with Billy’s help, we cut the tops off a couple of the cedar trees in the garden that support the rainwater catching garden tarp, but were block a lot of light.  We got the garden tarp hung and position to catch some of the forecasted rain, and we also finished pushing back the brush from the fence.  A lot of dirty sweaty work, but at least it was a beautiful day.

There’s still plenty to do in the garden, but I’ll start delegating some of that to the volunteers and get back to the solar hot water projects because there’s going to be plenty of dirty stinky volunteers wanting a hot shower soon enough.